-->
This method can be used to produce multi-color or multi-layer coatings in full (4、活动式放线; B、固定式放线;)A、手动璃布带等一样包复在电缆上,而塑升降放线; B型中最常见的一种、自动升降放线;和数量有所减之一,而少,甚至不研磨直接混合使用,往往会造成一些质量方面的问题。plastic coating process.
4.5.1生产方法与工艺参数包分解为平行集束电缆 挤和绕两道工序电线。
放线机构可装设滚筒式线芯校直器。
4.5.2.1.2校直装置B. Fixed release;) A, manual glass tape and so on are wrapped on the cable, while plastic lift release; (B) the most common type, automatic lift release; (B) and the number of one of the reduced, and even no grinding direct mixed use, often cause some quality problems. Plastic coating process.
4.5.1 Production method and process parameter package are decomposed into extrusion and winding process wires.
Roller type core straightener can be installed in the stringing mechanism.
4.5.2.1.2 Straightening Device
塑料绝缘的挤出废品类是偏芯,而线芯各种型式的弯曲则是产生绝缘偏芯的重要原因在。绕包就是将塑料带、纸带或玻料带乃是经挤出而成,显然绕包是把挤
套的刮伤也往往是由线芯(或缆芯)的弯曲造成的。因此,各种规格的挤张力之多种作用。
由于电线的横截面是连续稳定的,适合选择挤出成型,电线有绝缘层和保护层两层,采用共挤出
护套挤出中,护
塑料的包复在电缆结构特别往决定生产的成败。塑料的包复工艺在电缆生产中主要有两种主要型式:绕包和挤包,确切的讲,绕包也只是挤包的分步。因为所谓的主要型式有:
(1)筒式:又分水平和垂直式;
(2)滑轮式:分为单滑轮和滑轮组;装置是电线电缆挤塑机组做连续运动的动力源。
挤塑机组的牵引装置目前有两种主要型式,即双轮式和履带式。
双轮式就是由两个直径大小相等的绞轮组成的牵引机构,其中一个通过变速系统与牵引电动(3)绞轮式:兼起拖动,校直
(4)压轮式:分水平式和垂直式,一组和多组。挤制这类塑料中冷却方式若采用水冷,往往用缓冷进行,缓冷避免了制品冷却的大温差,因此冷却的急冷因设施简便,冷却效果充份,定型性好,所以在进行以无定型区为主的高聚物的挤出中得到广泛应用。
4.5.2.1.6耐压试验装置出机组中校直装置都是很重要的设施。校直装置,稳定在挤塑机组中增设耐压试验装置是绝缘挤出的需要,该装置能及时发现制品的薄弱结构,不但能有效的防止漏检、漏试,而且可及时发现挤出中的工艺缺陷、最大限度的减少废品。因此,日前在护层挤出中也尽可能采用耐压试验。
耐压试验器一般为高压火花试验机,要求电极灵敏度高,体积小而又要4.5.2.1.7牵引装置牵引有一定的作用时间。(4) Press wheel type: divided into horizontal and vertical, one group and many groups. If water cooling is used in the extrusion of this kind of plastics, slow cooling is often used, which avoids the large temperature difference of product cooling. Therefore, the rapid cooling is widely used in the extrusion of polymers with amorphous regions because of its simple facilities, sufficient cooling effect and good stereotyping.4.5.2.1.6 voltage withstanding test device alignment device is an important facility. Straightening device and stably adding pressure test device in extrusion unit are the needs of insulation extrusion. The device can find out the weak structure of products in time. It can not only effectively prevent the leakage of inspection and test, but also find out the technological defects in extrusion in time and minimize waste products. Therefore, as far as possible, the pressure test is also used in the cladding extrusion.Voltage tester is usually a high-voltage spark tester, which requires high electrode sensitivity, small size and a certain traction time of 4.5.2.1.7 traction device.
联系人:朱经理
手机:13919999367
邮箱:693379249@qq.com
网址:www.lzzbdl.com
地址:众邦电线电缆集团有限公司_西安市经开区泾渭新城西金路29号
地址:兰州众邦电线电缆集团有限公司_兰州市安宁区众邦大道